3D model (JSmol)
|ECHA InfoCard||Lua error in Module:Wikidata at line 879: attempt to index field 'wikibase' (a nil value). Lua error in Module:Wikidata at line 879: attempt to index field 'wikibase' (a nil value).|
|Molar mass||54.09 g/mol|
or refrigerated liquid
|Density||0.64 g/cm³ at -6 °C, liquid|
|Viscosity||0.25 cP at 0 °C|
|Main hazards||Flammable, irritative|
|Except where noted otherwise, data are given for|
materials in their standard state
(at 25 °C, 100 kPa)
Infobox disclaimer and references
1,3-Butadiene is a simple conjugated diene. It is an important industrial chemical used as a monomer in the production of synthetic rubber. When the word butadiene is used, most of the time it refers to 1,3-butadiene.
In 1863, a French chemist isolated a previously unknown hydrocarbon from the pyrolysis of amyl alcohol. This hydrocarbon was identified as butadiene in 1886, after Henry Edward Armstrong isolated it from among the pyrolysis products of petroleum. In 1910, the Russian chemist Sergei Lebedev polymerized butadiene, and obtained a material with rubber-like properties. This polymer was, however, too soft to replace natural rubber in many roles, especially automobile tires.
The butadiene industry originated in the years leading up to World War II. Many of the belligerent nations realized that in the event of war, they could be cut off from rubber plantations controlled by the British Empire, and sought to remove their dependence on natural rubber. In 1929, Eduard Tschunker and Walter Bock, working for IG Farben in Germany, made a copolymer of styrene and butadiene that could be used in automobile tires. Worldwide production quickly ensued, with butadiene being produced from grain alcohol in the Soviet Union and the United States and from coal-derived acetylene in Germany.
In the United States, western Europe, and Japan, butadiene is produced as a byproduct of the steam cracking process used to produce ethylene and other olefins. When mixed with steam and briefly heated to very high temperatures (often over 900 °C), aliphatic hydrocarbons give up hydrogen to produce a complex mixture of unsaturated hydrocarbons, including butadiene. The quantity of butadiene produced depends on the hydrocarbons used as feed. Light feeds, such as ethane, give primarily ethylene when cracked, but heavier favor the formation of heavier olefins, butadiene, and aromatic hydrocarbons.
Butadiene is typically isolated from the other four-carbon hydrocarbons produced in steam cracking by extraction into a polar aprotic solvent such as acetonitrile or dimethylformamide, from which it is then stripped by distillation.
Butadiene can also be produced by the catalytic dehydrogenation of normal butane. The first such commercial plant, producing 65,000 tons per year of butadiene, began operations in 1957 in Houston, Texas.
In other parts of the world, including eastern Europe, China, and India, butadiene is also produced from ethanol. While not competitive with steam cracking for producing large volumes of butadiene, lower capital costs make production from ethanol a viable option for smaller-capacity plants. Two processes are in use.
This process was the basis for the Soviet Union's synthetic rubber industry during and after World War II, and it remains in limited use in Russia and other parts of eastern Europe.
In the other, two-step process, developed by the Russian chemist Ivan Ostromislensky, ethanol is oxidized to acetaldehyde, which reacts with additional ethanol over a tantalum-promoted porous silica catalyst at 325–350 °C to yield butadiene:
This process was used in the United States to produce government rubber during World War II, and remains in use today in China and India.
Most butadiene is polymerized to produce synthetic rubber. While polybutadiene itself is a very soft, almost liquid material, polymers prepared from mixtures of butadiene with styrene or acrylonitrile, such as ABS, are both tough and elastic. Styrene-butadiene rubber is the material most commonly used for the production of automobile tires.
Smaller amounts of butadiene are used to make nylon via the intermediate adiponitrile, other synthetic rubber materials such as chloroprene, and the solvent sulfolane. Butadiene is used in the industrial production of cyclododecatriene via a trimerization reaction.
This article possibly contains original research. (February 2008) (Learn how and when to remove this template message)
At acute high exposure, damage to the central nervous system will start to occur. Symptoms such as distorted blurred vision, vertigo, general tiredness, decreased blood pressure, headache, nausea, decreased pulse rate, and fainting may be witnessed. As the exposure to butadiene occurs at a higher level and for a longer duration, the effects witnessed will become more serious. The actual link between chronic effects of butadiene has been argued over the years, though human epidemiological studies have been performed over the years showing increased risks in serious adverse health effects.
Several studies show butadiene exposure increases risk in cardiovascular diseases and cancer. Animal data suggests the carcinogenic effects of butadiene may have a higher sensitivity to females over men when exposed to the chemical. While this data reveals important implications to the risks of human exposure to butadiene, more data is necessary to draw more conclusive risk assessments. There is also a lack of human data on the effects butadiene has on reproductive and developmental effects shown to occur in mice, but animal studies have shown breathing butadiene during pregnancy can increase the number of birth defects.
Storage of butadiene as a compressed, liquified gas carries a specific and unusual hazard. Over time, polymerization can begin, creating a crust of solidified material (which looks like popcorn) inside the cylinder. If the cylinder is then disturbed, the crust can contact the liquid and initiate an auto-catalytic polymerization. The heat released accelerates the reaction, possibly leading to cylinder rupture. Inhibitors are typically added to reduce this hazard, but butadiene cylinders should still be considered short-shelf life items.
- Caventou, E. (1863), Annalen der Chemie und Pharmacie 127, 93.
- Armstrong, H.E. Miller, A.K. (1886). "The decomposition and genesis of hydrocarbons at high temperatures. I. The products of the manufacture of gas from petroleum." Journal of the Chemical Society 49, 80.
- Sun, H.P. Wristers, J.P. (1992). Butadiene. In J.I. Kroschwitz (Ed.), Encyclopedia of Chemical Technology, 4th ed., vol. 4, pp. 663–690. New York: John Wiley & Sons.
- Beychok, M.R. and Brack, W.J., "First Postwar Butadiene Plant", Petroleum Refiner, June 1957.
- Kirshenbaum, I. (1978). Butadiene. In M. Grayson (Ed.), Encyclopedia of Chemical Technology, 3rd ed., vol. 4, pp. 313–337. New York: John Wiley & Sons.